Learn About the Law
Get help with your legal needs
FindLaw’s Learn About the Law features thousands of informational articles to help you understand your options. And if you’re ready to hire an attorney, find one in your area who can help.
Current as of October 02, 2022 | Updated by FindLaw Staff
(a) For each industrial waste landfill subject to the reporting requirements of this subpart, calculate annual modeled CH4 generation according to the applicable requirements in paragraphs (a)(1) through (a)(3) of this section. Apply Equation TT–1 of this section for each waste stream disposed of in the landfill and sum the CH4 generation rates for all waste streams disposed of in the landfill to calculate the total annual modeled CH4 generation rate for the landfill.
(1) Calculate annual modeled CH4 generation using Equation TT–1 of this section.
Where:
GCH4 = Modeled methane generation in reporting year T (metric tons CH4 ).
X = Year in which waste was disposed.
S = Start year of calculation. Use the year 1960 or the opening year of the landfill, whichever is more recent.
T = Reporting year for which emissions are calculated.
WX = Quantity of waste disposed in the industrial waste landfill in year X from measurement data and/or other company records (metric tons, as received (wet weight)).
DOCX = Degradable organic carbon for waste disposed in year X from Table TT–1 to this subpart or from measurement data [as specified in paragraph (a)(3) of this section], if available [fraction (metric tons C/metric ton waste) ].
DOCF = Fraction of DOC dissimilated (fraction); use the default value of 0.5. If measured values of DOC are available using the 60–day anaerobic biodegradation test procedure identified in § 98.464(b)(4)(i), use a default value of 1.0.
MCF = Methane correction factor (fraction). Use the default value of 1 unless there is active aeration of waste within the landfill during the reporting year. If there is active aeration of waste within the landfill during the reporting year, use either the default value of 1 or select an alternative value no less than 0.5 based on site-specific aeration parameters.
F = Fraction by volume of CH4 in landfill gas (fraction, dry basis, corrected to 0% oxygen). If you have a gas collection system, use the annual average CH4 concentration from measurement data for the current reporting year; otherwise, use the default value of 0.5.
k = Decay rate constant from Table TT–1 to this subpart (yr–1). Select the most applicable k value for the majority of the past 10 years (or operating life, whichever is shorter).
(2) Waste stream quantities. Determine annual waste quantities as specified in paragraphs (a)(2)(i) through (ii) of this section for each year starting with January 1, 1960 or the year the landfills first accepted waste if after January 1, 1960, up until the most recent reporting year. The choice of method for determining waste quantities will vary according to the availability of historical data. Beginning in the first emissions reporting year (2011 or later) and for each year thereafter, use the procedures in paragraph (a)(2)(i) of this section to determine waste stream quantities. These procedures should also be used for any year prior to the first emissions reporting year for which the data are available. For other historical years, use paragraph (a)(2)(i) of this section, where waste disposal records are available, and use the procedures outlined in paragraph (a)(2)(ii) of this section when waste disposal records are unavailable, to determine waste stream quantities. Historical disposal quantities deposited (i.e., prior to the first year in which monitoring begins) should only be determined once, as part of the first annual report, and the same values should be used for all subsequent annual reports, supplemented by the next year's data on new waste disposal.
(i) Determine the quantity of waste (in metric tons as received, i.e., wet weight) disposed of in the landfill separately for each waste stream by any one or a combination of the following methods.
(A) Direct mass measurements.
(B) Direct volume measurements multiplied by waste stream density determined from periodic density measurement data or process knowledge.
(C) Mass balance procedures, determining the mass of waste as the difference between the mass of the process inputs and the mass of the process outputs.
(D) The number of loads (e.g., trucks) multiplied by the mass of waste per load based on the working capacity of the container or vehicle.
(ii) Determine the historical disposal quantities for landfills using the Waste Disposal Factor approach in paragraphs (a)(2)(ii)(A) and (B) of this section when historical production or processing data are available. If production or processing data are available for a given year, you must use Equation TT–3 of this section for that year. Determine historical disposal quantities using the method specified in paragraph (a)(2)(ii)(C) of this section when historical production or processing data are not available, and for waste streams received from an off-site facility when historical disposal quantities cannot be determined using the methods specified in paragraph (a)(2)(i) of this section.
(A) Determining Waste Disposal Factor: For each waste stream disposed of in the landfill, calculate the average waste disposal rate per unit of production or unit throughput using all available waste quantity data and corresponding production or processing rates for the process generating that waste or, if appropriate, the facility, using Equation TT–2 of this section.
Where:
WDF = Average waste disposal factor as determined for the first annual report required for this industrial waste landfill (metric tons per production unit).
X = Year in which waste was disposed. Include only those years for which disposal and production data are both available; the years do not need to be sequential.
Y1 = First year in which disposal and production/throughput data are both available.
Y2 = First year for which GHG emissions from this industrial waste landfill must be reported.
N = Number of years for which disposal and production/throughput data are both available.
Wx = Quantity of waste placed in the industrial waste landfill in year X from measurement data and/or other company records (metric tons, as received (wet weight)).
Px = Quantity of product produced or feedstock entering the process or facility in year X from measurement data and/or other company records (production units). You must use the same basis for all years in the calculation. That is, Px must be determined based on production (quantity of product produced) for all “N” years or Px must be determined based on throughput (quantity of feedstock) for all “N” years.
(B) Calculate waste: For each waste stream disposed of in the landfill, calculate the waste disposal quantities for historic years in which direct waste disposal measurements are not available using historical production data and Equation TT–3 of this section.
Where:
X = Historic year in which waste was disposed.
Wx = Calculated quantity of waste placed in the landfill in year X (metric tons).
WDF = Average waste disposal factor from Equation TT–2 of this section (metric tons per production unit).
Px = Quantity of product produced or feedstock entering the process or facility in year X from measurement data and/or other company records (production units). You must use the same basis for Px (either production only or throughput only) as used to determine WDF in Equation TT–2 of this section.
(C) For any year in which historic production or processing data are not available such that historic waste quantities cannot be estimated using Equation TT–3 of this section, calculate an average annual bulk waste disposal quantity using either Equation TT–4a of this section when data are available consecutively for the most recent disposal years or Equation TT–4b of this section when data are available for sporadic (non-consecutive) years.
Where:
WX = Quantity of waste placed in the landfill in year X (metric tons, wet basis). This annual bulk waste disposal quantity applies for all years from “YrOpen” to “YrData” inclusive.
LFC = Capacity of the landfill used (or the total quantity of waste-in-place) at the end of the “YrData” from design drawings or engineering estimates (metric tons). For closed landfills for which waste quantity data are not available, use the landfill's design capacity.
YrData = The year prior to the year when waste disposal data are first available for all subsequent years from company records or from Equation TT–3 of this section. For landfills for which waste quantity data are not available, the year in which the landfill last received waste.
YrOpen = Year 1960 or the year in which the landfill first received waste from company records, whichever is more recent. If no data are available for estimating YrOpen for a closed landfill, use 1960 as the default “YrOpen” for the landfill.
Where:
WX = Quantity of waste placed in the landfill in year X (metric tons, wet basis). This annual bulk waste disposal quantity applies for all years for which waste quantity data are not available from company records or from Equation TT–3 of this section.
WIP = Quantity of waste in-place at the start of the reporting year from design drawings or engineering estimates (metric tons). For closed landfills for which waste in-place quantities are not available, use the landfill's design capacity.
Wmeas,n = Annual quantity of waste placed in the landfill for the nth measurement year from company records or from Equation TT–3 of this section.
YrLast = The last year, prior to the reporting year, that the landfill received waste.
YrOpen = Year 1960 or the year in which the landfill first received waste from company records, whichever is more recent. If no data are available for estimating YrOpen for a closed landfill, use 1960 as the default “YrOpen” for the landfill.
NYrData = The number of years for which annual waste disposal quantities are available from company records or from Equation TT–3 of this section from YrOpen to YrLast inclusive.
(3) Degradable organic content (DOC). For any year, X, in Equation TT–1 of this section, use either the applicable default DOC values provided in Table TT–1 of this subpart or determine values for DOCx as specified in paragraphs (a)(3)(i) through (iv) of this section. When developing historical waste quantity data, you may use default DOC values from Table TT–1 of this subpart for certain years and determined values for DOCx for other years. The historical values for DOC or DOCx must be developed only for the first annual report required for the industrial waste landfill; and used for all subsequent annual reports (e.g., if DOC for year x=1990 was determined to be 0.15 in the first reporting year, you must use 0.15 for the 1990 DOC value for all subsequent annual reports).
(i) For the first year in which GHG emissions from this industrial waste landfill must be reported, determine the DOCx value of each waste stream disposed of in the landfill no less frequently than once per quarter using the methods specified in § 98.464(b). Calculate annual DOCx for each waste stream as the arithmetic average of all DOCx values for that waste stream that were measured during the year.
(ii) For subsequent years (after the first year in which GHG emissions from this industrial waste landfill must be reported), either use the DOCx of each waste stream calculated for the most recent reporting year for which DOC values were determined according to paragraph (a)(3)(i) of this section, or determine new DOC values for that year following the requirements in paragraph (a)(3)(i) of this section. You must determine new DOC values following the requirements in paragraph (a)(3)(i) of this section if changes in the process operations occurred during the previous reporting year that can reasonably be expected to alter the characteristics of the waste stream, such as the water content or volatile solids concentration. Should changes to the waste stream occur, you must revise the GHG Monitoring Plan as required in § 98.3(g)(5)(iii) and report the new DOCx value according to the requirements of § 98.466.
(iii) If DOCx measurement data for each waste stream are available according to the methods specified in § 98.464(b) for years prior to the first year in which GHG emissions from this industrial waste landfill must be reported, determine DOCx for each waste stream as the arithmetic average of all DOCx values for that waste stream that were measured in Year X. A single measurement value is acceptable for determining DOCx for years prior to the first reporting year.
(iv) For historical years for which DOCx measurement data, determined according to the methods specified in § 98.464(b), are not available, determine the historical values for DOCx using the applicable methods specified in paragraphs (a)(3)(iv)(A) and (B) of this section. Determine these historical values for DOCx only for the first annual report required for this industrial waste landfill; historical values for DOCx calculated for this first annual report should be used for all subsequent annual reports.
(A) For years in which waste stream-specific disposal quantities are determined (as required in paragraphs (a)(2) (ii)(A) and (B) of this section), calculate the average DOC value for a given waste stream as the arithmetic average of all DOC measurements of that waste stream that follow the methods provided in § 98.464(b), including any measurement values for years prior to the first reporting year and the four measurement values required in the first reporting year. Use the resulting waste-specific average DOC value for all applicable years (i.e., years in which waste stream-specific disposal quantities are determined) for which direct DOC measurement data are not available.
(B) For years for which bulk waste disposal quantities are determined according to paragraphs (a)(2)(ii)(C) of this section, calculate the weighted average bulk DOC value according to the following: Calculate the average DOC value for each waste stream as the arithmetic average of all DOC measurements of that waste stream that follows the methods provided in § 98.464(b) (generally, this will include only the DOC values determined in the first year in which GHG emissions from this industrial waste landfill must be reported); calculate the average annual disposal quantity for each waste stream as the arithmetic average of the annual disposal quantities for each year in which waste stream-specific disposal quantities have been determined; and calculate the bulk waste DOC value using Equation TT–5 of this section. Use the bulk waste DOC value as DOCx for all years for which bulk waste disposal quantities are determined according to paragraphs (a)(2)(ii)(C) of this section.
Where:
DOCbulk = Degradable organic content value for bulk historical waste placed in the landfill (mass fraction).
N = Number of different waste streams placed in the landfill.
n = Index for waste stream.
DOCave,n = Average degradable organic content value for waste stream “n” based on available measurement data (mass fraction).
Wave,n = Average annual quantity of waste stream “n” placed in the landfill for years in which waste stream-specific disposal quantities have been determined (metric tons per year, wet basis).
(b) For each landfill, calculate CH4 generation (adjusted for oxidation in cover materials) and CH4 emissions (taking into account any CH4 recovery, if applicable, and oxidation in cover materials) according to the applicable methods in paragraphs (b)(1) through (b)(3) of this section.
(1) For each landfill, calculate CH4 generation, adjusted for oxidation, from the modeled CH4 (GCH4 from Equation TT–1 of this section) using Equation TT–6 of this section.
Where:
MG = Methane generation, adjusted for oxidation, from the landfill in the reporting year (metric tons CH4).
GCH4 = Modeled methane generation rate in reporting year from Equation TT–1 of this section (metric tons CH4).
OX = Oxidation fraction from Table HH–4 of subpart HH of this part.
(2) For landfills that do not have landfill gas collection systems operating during the reporting year, the CH4 emissions are equal to the CH4 generation (MG) calculated in Equation TT–6 of this section.
(3) For landfills with landfill gas collection systems in operation during any portion of the reporting year, perform all of the calculations specified in paragraphs (b)(3)(i) through (iv) of this section.
(i) Calculate the quantity of CH4 recovered according to the requirements at § 98.343(b).
(ii) Calculate CH4 emissions using the Equation HH–6 of § 98.343(c)(3)(i), except use GCH4 determined using Equation TT–1 of this section in Equation HH–6 of § 98.343(c)(3)(i).
(iii) Calculate CH4 generation (MG) from the quantity of CH4 recovered using Equation HH–7 of § 98.343(c)(3)(ii).
(iv) Calculate CH4 emissions from the quantity of CH4 recovered using Equation HH–8 of § 98.343(c)(3)(ii).
Cite this article: FindLaw.com - Code of Federal Regulations Title 40. Protection of Environment § 40.98.463 Calculating GHG emissions - last updated October 02, 2022 | https://codes.findlaw.com/cfr/title-40-protection-of-environment/cfr-sect-40-98-463/
FindLaw Codes may not reflect the most recent version of the law in your jurisdiction. Please verify the status of the code you are researching with the state legislature or via Westlaw before relying on it for your legal needs.
A free source of state and federal court opinions, state laws, and the United States Code. For more information about the legal concepts addressed by these cases and statutes, visit FindLaw's Learn About the Law.
Get help with your legal needs
FindLaw’s Learn About the Law features thousands of informational articles to help you understand your options. And if you’re ready to hire an attorney, find one in your area who can help.
Search our directory by legal issue
Enter information in one or both fields (Required)