Skip to main content
Find a Lawyer

Code of Federal Regulations Title 29. Labor § 29.1910.133 Eye and face protection

Current as of January 02, 2025 | Updated by Findlaw Staff

(a) General requirements.

(1) The employer shall ensure that each affected employee uses appropriate eye or face protection when exposed to eye or face hazards from flying particles, molten metal, liquid chemicals, acids or caustic liquids, chemical gases or vapors, or potentially injurious light radiation.

(2) The employer shall ensure that each affected employee uses eye protection that provides side protection when there is a hazard from flying objects. Detachable side protectors (e.g. clip-on or slide-on side shields) meeting the pertinent requirements of this section are acceptable.

(3) The employer shall ensure that each affected employee who wears prescription lenses while engaged in operations that involve eye hazards wears eye protection that incorporates the prescription in its design, or wears eye protection that can be worn over the prescription lenses without disturbing the proper position of the prescription lenses or the protective lenses.

(4) Eye and face PPE shall be distinctly marked to facilitate identification of the manufacturer.

(5) The employer shall ensure that each affected employee uses equipment with filter lenses that have a shade number appropriate for the work being performed for protection from injurious light radiation. The following is a listing of appropriate shade numbers for various operations.

Filter Lenses for Protection Against Radiant Energy

Operations

Electrode Size
1/32 in.

Arc Current

Minimum *
Protective
Shade

Shielded metal arc welding

Less than 3․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

Less than 60․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

7

3-5․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

60-160․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

8

5-8․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

160-250․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

More than 8․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

250-550․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

11

Gas metal arc welding and flux cored arc welding

less than 60․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

7

60-160․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

160-250․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

250-500․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

Gas Tungsten arc welding

less than 50․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

8

50-150․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

8

150-500․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

Air carbon

(Light)․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

less than 500․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

Arc cutting

(Heavy)․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

500-1000․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

11

Plasma arc welding

less than 20․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

6

20-100․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

8

100-400․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

400-800․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

11

Plasma arc cutting

(light)**․․․․․․․․․․․․․․․․․․․․․․․․․․

less than 300․․․․․․․․․․․․․․․․․․․․․․․․․․․․

8

(medium)**․․․․․․․․․․․․․․․․․․․․․․․․

300-400․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

9

(heavy)**․․․․․․․․․․․․․․․․․․․․․․․․․․

400-800․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

10

Torch brazing

․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

3

Torch soldering

․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

2

Carbon arc welding

․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

14

Filter Lenses for Protection Against Radiant Energy

Operations

Plate thickness—
inches

Plate thickness—
mm

Minimum *
Protective
Shade

Gas Welding:

Light

Under 1/8․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

Under 3.2․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

4

Medium

1/8 to 1/2․․․․․․․․․․․․․․․․․․․․․․․․

3.2 to 12.7․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

5

Heavy

Over 1/2․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

Over 12.7․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

6

Oxygen cutting:

Light

Under 1․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

Under 25․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

3

Medium

1 to 6․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

25 to 150․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

4

Heavy

Over 6․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

Over 150․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․․

5

* As a rule of thumb, start with a shade that is too dark to see the weld zone. Then go to a lighter shade which gives sufficient view of the weld zone without going below the minimum. In oxyfuel gas welding or cutting where the torch produces a high yellow light, it is desirable to use a filter lens that absorbs the yellow or sodium line in the visible light of the (spectrum) operation.

** These values apply where the actual arc is clearly seen. Experience has shown that lighter filters may be used when the arc is hidden by the workpiece.

(b) Criteria for protective eye and face protection.

(1) Protective eye and face protection devices must comply with any of the following consensus standards:

(i) ANSI/ISEA Z87.1–2010, Occupational and Educational Personal Eye and Face Protection Devices, incorporated by reference in § 1910.6;

(ii) ANSI Z87.1–2003, Occupational and Educational Personal Eye and Face Protection Devices, incorporated by reference in § 1910.6;  or

(iii) ANSI Z87.1–1989 (R–1998), Practice for Occupational and Educational Eye and Face Protection, incorporated by reference in § 1910.6;

(2) Protective eye and face protection devices that the employer demonstrates are at least as effective as protective eye and face protection devices that are constructed in accordance with one of the above consensus standards will be deemed to be in compliance with the requirements of this section.

Previous Part of Code Next Part of Code
Back to Chapter List

Cite this article: FindLaw.com - Code of Federal Regulations Title 29. Labor § 29.1910.133 Eye and face protection - last updated January 02, 2025 | https://codes.findlaw.com/cfr/title-29-labor/cfr-sect-29-1910-133/

FindLaw Codes may not reflect the most recent version of the law in your jurisdiction. Please verify the status of the code you are researching with the state legislature before relying on it for your legal needs.

Was this helpful?

Welcome to FindLaw's Cases & Codes

A free source of state and federal court opinions, state laws, and the United States Code. For more information about the legal concepts addressed by these cases and statutes, visit FindLaw’s Learn About the Law.

Go to Learn About the Law

Latest Blog Posts

For Legal Professionals

Learn About The Law

Get help with your legal needs

FindLaw’s Learn About the Law features thousands of informational articles to help you understand your options. And if you’re ready to hire an attorney, find one in your area who can help.

Go to Learn About the Law

Need to Find an Attorney?

Search our directory by legal issue

Enter information in one or both fields (Required)

Copied to clipboard